产品中心

Products

undefined
+
  • undefined

注塑级HY1500

所属分类:

江苏华洋尼龙有限公司是一家以高分子新材料、工程塑料、尼龙塑料件、涤纶纱线生产、销售和服务为主业的创新型企业。华洋尼龙在当地拥有多家大型生产基地

关键词: 尼龙66切片  |  工程改性塑料  |  尼龙扎带

详细参数


劲旅环境

技术数据表 Technical Data Sheet

PA66 HY1500

通用型树脂 / General Purpose Resin

 

产品信息 Product Information

名称:聚己二酰己二胺 66 /尼龙 66 树脂

Name: Polyamide 66/Nylon 66 Resin

CAS: 32131-17-2

 

产品描述 Product Description

HY1500 为通用型注塑级尼龙 66 产品,抗张强度高、韧性好、耐冲击性好;具有较好的流动性、自润滑性、耐磨性、抗低温性和自熄性。

HY1500 is a general purpose Nylon 66 resin. This resin offers a well-balanced combination of engineering properties characterized by high strength; good toughness; high impact; good flow and surface lubricity; abrasion resistance; resistant low temperature; self extinguishment.

 

产品安全 Product Safety

急救措施的描述

吸入

如意外吸入蒸汽或分解产物,将受害者移到空气新鲜处。

皮肤接触

无需特殊的防范措施。

眼睛接触

不是一种预期的接触途径。无需立即就医。

食入

不是一种预期的接触途径。如吞咽: 立即呼叫中毒中心或医生。

特别危险性

热分解会导致释放出刺激性和有毒气体和蒸气

Description of first aid measures

Inhalation Move to fresh air in case of accidental inhalation of vapours or decomposition products.

Skin Contact

No special technical protective measures are necessary.

Eye Contact Not an expected route of exposure. Immediate medical attention is not required.

Ingestion Not an expected route of exposure. If swallowed, call a poison control centre or physician immediately.

Special Hazard

Thermal decomposition can lead to release of irritating and toxic gases and vapours

 

典型应用 Typical Applications

HY1500 除一般应用外,特别适用于对流动性能及耐低温性能要求较高的注塑制品,终端应用主要集中在机械、电子电气、仪器仪表、汽车部件、铁路、家电、通讯、扎带及精密工程制品等,亦可用于生产医疗器械、体育用品、日用品等。

In addition to general applications, HY1500 is especially suitable for injection molding products with high requirements for fluidity and low temperature resistance. It’s terminal applications are mainly in machinery, electronics and electrical, instruments and meters, automobile components, railways, home appliances, communications, cable ties and precision engineering products, etc. It can also be used to produce medical equipments, sporting goods, daily necessities and so on.

 

使用指南 Guidelines for Molding

1. 本产品的包装为防潮包装,在未开封前水分含量恒定,建议开封后尽快使用。在使用已开封的产品前,建议对其进行必要的除湿干燥,以确保注塑制品质量和注塑过程的稳定性。干燥温度不宜过高,最高不应超过 70℃;时间不宜过长,最长不应超过 5 小时。

Our nylon 66 resins arrive packaged in moisture-protected containers. If you didn’t open the original package prior to use, then drying is not necessary. However, if drying is necessary for using the opened package, we recommend that you use dehumidifying with maximum temperature of 70 ℃ or 5 hours.

2. 注塑温度不宜过高,建议以 275 ℃ ~ 295 ℃为宜。过高的温度容易使尼龙 66 树脂在高温状态下裂解,产品性能下降。

The recommend melt temperatures are 275 ℃ to 295 ℃. Nylon 66 resin is easy to decompose under too high temperature,and then decrease product properties.

3. 在注塑生产过程中,应控制模具温度,以 15 ℃ ~ 90 ℃为宜,建议模具温度保持在温度区间的上线,过低的模具温度会导致尼龙 66 树脂流动性变差,制品表面光洁度差或表面缺陷、制品收缩率高。

Maintain mould surface temperatures in range of 15 ℃ ~ 90 ℃. We recommend the temperatures on the high end. Under low temperature nylon 66 resin flows worse, bad or defect appearance, shrinkage of the moulded part.

4. 保压时间至少应长于浇口物料的凝固时间。

Hold pressure time should be set until the gate freezes.

5. 为提高注塑制品质量,建议在新料中不使用或尽量少使用回料。在使用回料前,应对 其进行相应的干燥除湿处理,保证其水分含量与新料接近。须注意,随着加工次数的增加,回料的性能下降很明显, 请谨慎使用经多次加工的回料。

As to get high performance of the moulded part, we recommend no use or less regrind material mixed with virgin resin。Regrind must be dry when moulded. The preferred procedure is to grind and reuse immediately after moulding, otherwise regrind shows significant property loss

 

免责声明 Disclaimer

技术数据表内的典型参数是基于相关标准检测得出的数据,供客户在选择产品时作为参考,并不意味着华洋尼龙对产品性能指标的承诺。

The typical parameters in the TDS is to detect based on relevant standards, as a reference for customers to choose products, which does not mean that the commitment of Huayang Nylon on performance indicators.

华洋尼龙保留对本技术数据表进行修订的权利,恕不另行通知;如有需要请向我们索取最新版本。

Huayang Nylon reserves the right to revise this manual without prior notice; if necessary, please ask us for the latest version.

 

典型参数 Typical Parameters

项 目
Item
单位
Unit
测试标准
Test Standard
典型值
Typical Value
物 化性 能 physical&chemical properties      
相对粘度
relative viscosity
  QB  2.40±0.05
端胺基
-NH2
  Meg/kg QB    42±5
端羧基
-COOH
  Meq/kg QB  
黑粒
Black specks
% QB  
含水率
water content
mg/kg GB/12006.2-89    ≤3500
机 械 性 能 Mechanical properties      
拉伸强度
tensile strength
Mpa ISO527   ≥70
断裂伸长率
elongation,at bread
% ISO527   12.5
弯曲强度
flexural strength
MPa ISO178 92
弯曲模量
flexural modulus
MPa ISO178 2060
冲击强度(无缺口)
charpy impact strenth
   KJ/m² ISO179 NB
缺口冲击强度
charpy notched impact strength
   KJ/m² ISO179 4.4
执性能 thermal properties      
熔体流动速率
melt flow rate
   g/10min ISO1133 90
熔点
melting point
 ℃ DSC 260
热变形温度
heat deflection temperature
 ℃ ISO 75(0.45MPa) 186

产品咨询